胤旭機電網最新報道 >> PORTESCAP步進電機_瑞士品牌_型號P532 258 0.7-10 : PORTESCAP 步進電機 P532 258 0.7-10 高速渦輪盤步進電機P532 Portescap 渦輪盤步進電機具有市面上任何其他小直徑步進電機都無可匹敵的卓越動態性能。憑借其獨特的超簿盤式磁鐵,能夠以更小……
PORTESCAP 步進電機 P532 258 0.7-10
高速渦輪盤步進電機P532
Portescap 渦輪盤步進電機具有市面上任何其他小直徑步進電機都無可匹敵的卓越動態性能。憑借其獨特的超簿盤式磁鐵,能夠以更小的尺寸提供更高的步分辨率,與傳統步進電機相比,加速度和最大速度都有顯著提升。
如果某類應用既需要步進電機的精度,又需要無刷直流電機的速度/加速度,則渦輪盤步進電機是其不二選擇。閉環控制使其比伺服解決方案更具競爭優勢。KRESS電機
性能及特點
精確 - 特別適合微步進
速度快 - 渦輪盤步進電機在保持準確定位的條件下提供了所有步進電機中最高的加速度和最高的極限速度
獨特 - 低定位扭矩、高度可定制
可調 - 每轉步數比類似直徑的步進電機多
按需求定制
滑動或滾珠軸承
各種繞組
軸定制 - 加長/縮短長度、滾花
加長引線,連接器
齒輪箱能夠提高扭矩
典型應用
臨床診斷微型電機應用
紡織導紗器
機械手臂
激光切割器
線切割 - EDM
Disc Magnet Stepper Motors P532 | |||||
Electrical Data |
P532 258 012 10/84 (series) |
P532 258 004 10/84 (series) | P532 258 004 10/84 (parallel) |
P532 258 0.7 10/84 (parallel) |
|
1 Resistance per Phase, typ | 27 | 8.8 | 2.2 | 0.4 | Ohms |
2 Inductance per Phase, typ | 64 | 20 | 5 | 0.7 | mH |
3 Nominal Phase Current (2 ph. On) | 0.4 | 0.7 | 1.4 | 3.7 | A |
4 Nominal Phase Current (1 ph. On) | 0.56 | 1 | 2 | 5.2 | A |
5 Back EMF Amplitude | 21 | 12 | 6 | 2.3 | V/kstep/s |
Coil independent parameters | |||||
6 Holding Torque, nominal current | 205 (29) | mNm (oz-in) | |||
7 Holding Torque, 1.5x nominal current (1) | 300 (42.5) | mNm (oz-in) | |||
8 Detent Torque | 40 (5.67) | mNm (oz-in) | |||
9 Rotor Inertia | 12 | kgm2 x 10-7 | |||
10 Step Angle | 4 | 3.6 | 3.6 | 3.6 | Degree |
11 Absolute Accuracy 2 ph. On, Full step mode | +/- 5% | % Full Step | |||
12 Steps Per Revolution | 100 | ||||
13 Ambient Temperature Range (operating) | -20 to 50 (-4 to 122) | °C (°F) | |||
14 Maximum Coil Temperature | 130 (266) | °C (°F) | |||
15 Thermal Resistance Coil-ambient (2) | 7 | 7.3 | 7.3 | 7.3 | °C/W |
16 Natural Resonance Frequency (nominal current) | 330 | Hz | |||
17 Electrical Time Constant | 2.3 | ms | |||
18 Angular Acceleration (nominal current) | 195,000 | rad/s2 | |||
19 Bearing Type | Ball | ||||
20 Dielectric Withstanding Voltage | 500 VRMS for 5 seconds (25@5N) | VAC | |||
21 Radial Shaft Play | 25@5N | µm | |||
22 Axial Shaft Play | 25@5N | µm | |||
23 Maximum Radial Shaft Load | 20 (72) | N (oz) | |||
24 Maximum Axial Shaft Load (3) | 30 (108) | N (oz) | |||
25 Weight | 250 (8.8) | g (oz) | |||
26 Power Rate (nominal current) | 35 | kW/s | |||
(1) Measured with 1 phase ON. The max coil temperature must be respected | |||||
(2) Motor unmounted | |||||
(3) Shaft must be supported when press-fitting a pulley or pinion |
咨詢與評論